hazmat label size requirements
Though the scope of this section of the HMR is not clearly defined, the use of language such as, “whether printed on or affixed to a package” seems to indicate that these specification apply to adhesive-backed labels affixed to a package in the same manner as they apply to the required colors, symbols, text, and numbers printed on a package. As a Shipper or Carrier of HazMat, make certain that the HazMat label printer you are using is in compliance with these regulations. Make sure your workers know the important aspects of chemical labeling, SDS and the new components of the GHS aligned HCS. It is printed outside the solid line inner border. In those instances of precise standards, I will refer you to the applicable regulation which should always be your source for compliance. Placard and Label Specifications. 2. Hazardous Materials Markings, Labeling and Placarding Guide (DOT Chart 15) Hazardous_Materials_Markings_Labeling_and_Placarding_Guide_508CLN.pdf. For packages equal to or less than 30 kg/30 L gross mass, but greater than 5 kg/5 L gross mass, a 6 mm text size is indicated. (The color standards, as I alluded to in the disclaimer, are very precise and will be referenced later whereas the size specifications will be addressed directly). Example: Yes, I would like to receive emails from Daniels Training Services. The minimum size of a pictogram on a GHS label shall be related to the minimum size of the GHS label; The minimum size of a GHS pictogram on a GHS label is usually much smaller than a transport pictogram (100mm x 100mm); A GHS label must be legible and prominently displayed; Europe, Switzerland, Singapore & Malaysia. These labels must withstand without deterioration or change in color, a 30-day exposure to reasonable transport conditions. There are a number of exceptions to the labeling requirements contained in 172.400a. Ft. capacity. 4. 1. Hazardous Materials Markings, Hazardous Materials Warning Labels, Hazardous Materials Warning Placards, General Guidelines on Use of Warning Labels and Placards. The specifications for the CARGO AIRCRAFT ONLY label are as follows: The background color of each label must be as prescribed – not as shown, since the images are black and white – in §172.411-448. December 1, 2013 PAST DUE TRAIN all employees on the new Label Elements and safety data sheets (SDS) formats and hazards. GHS transition period. ● Label’s hazard lettering must be at least 0.3 inches (7.3 mm) tall. (The labels shown in the exhibits are not shown to size. On all drums and/or tanks 30-gallon capacity or larger. For SPONTANEOUSLY COMBUSTIBLE or DANGEROUS WHEN WET labels, the words “Spontaneously” and “When Wet” must be shown in letters at least 5.1 mm (0.2″) high. All Labelmaster hazmat labels meet these strict specifications. For those listed below the label color must extend only to the inner border. General labeling requirements are contained in 49 CFR subpart E Part 172. 22 CCR §§66262.31 and 66262.32 require that all applicable U.S. Department of Transportation (DOT) marking and labeling requirements be met prior to offering waste for transportation. Since alternative labeling requirements may change in fewer than 4 years and employers must train employees to understand new label elements and the new Safety Data Sheet (SDS) format by Dec. 13, 2013, voluntarily switching to the revised HCS labeling now likely will reduce costs over the long run and reduce confusion in the workplace. In order to move hazardous waste, generators must be in compliance not only with Environmental Protection Agency (EPA) regulations but with the Department of Transportation (DOT) requirements for shipping, along with any state and local agency’s requirements … Labels, whether printed on a carton or affixed to the package, must meet the specific requirements of 49 CFR 172.411 through 172.448 in 49 CFR or Section 7.2.2.2 in IATA. All labels must be located on the same surface (if possible) – ideally near the proper shipping name 3. If the chemical was supplied before that date businesses can still use it as long as the label complies with the requirements that were in force at the time it was supplied. The Department of Transportation (DOT) regulates the movement of hazardous materials by road, rail, air and pipeline. DOT warning labels must meet the size and color requirements in 49 CFR 172.407 through 172.446.) The identification number markings must be: At least 12 mm in size for packages larger than 30 kg or L At least 6 mm in size for packages greater than 5 and up to 30 kg or L Of an adequate size for smaller packages A HazMat label may contain form identification information, including the name of the label manufacturer provided it complies with the following: Solely regarding Class 7 RADIOACTIVE materials [§172.407(g)]: The trefoil symbol on the HazMat labels listed below must meet the appropriate specifications in Appendix B to 49 CFR Part 172. Use the Hazardous Materials Table and HMR to determine the required hazard labels for a package; List the international labels that can be used in place of or in addition to DOT hazmat labels; List durability, size, color, and placement requirements for DOT labels; Identify non-compliant hazmat packages © Copyright 2021 Labelmaster. This requirement does not apply to other markings on the package, such as the Proper Shipping Name and the shipper’s or receiver’s name and address. The symbol, text, numbers, and border of a HazMat label must be shown in black except for the following: Paragraphs 3 through 6 of §172.407(d) are extremely technical, referring to a 72-hour fadeometer test, color charts on display in the USDOT office in Washington D.C., and the PANTONE® formula guide. ORM-D (other regulated materials for domestic transport only) was a marking for mail or shipping in the United States. According to §172.406 (a) (2) and §172.406 (e), display of more than one HazMat label on a package is not required. These are general requirements, but some hazardous materials (such as radioactive or spontaneously combustible substances) require specific labeling conventions. Text must be in letters at least 7.6 mm (0.3″) high. Must be a rectangle of at least 110 mm (4.3″) high and 120 mm (4.7″) in width. 1. This is due to a change to the HMR announced in the January 8, 2015 Federal Register to harmonize domestic regulations with the UN Model Regulations. 49 CFR - As of January 01, 2017, per HM-218H Final Rule, UPS will no longer accept a 49 CFR Hazmat shipping paper showing a Packing Group assignment for Class 1 Explosives, Division 4.1 Self-Reactive Substances (only) and Division 5.2 Organic Peroxides. Had enough? Hazard class labels must be durable and weather resistant. Play it safe when shipping flammable liquids with Labelmaster's Hazard Class 3 Labels . The MSDS does not have to list the amount that the … I think this is mostly of interest to the printers of HazMat labels and I’m not going to get into that here. The dotted line border shown on each label in 49 CFR 172.411 through 172.448 is not part of the specification, except as an alternative to a solid line in requirements of 172.406(d). (You can unsubscribe anytime), Learn More About USDOT/HazMat Transportation. Size. Both the International Civil Aviation Organization (ICAO) and International Maritime Organization (IMO) recently changed the required size of the text to be used when marking the United Nations Identification Number (UNID Number) on packages of dangerous goods/hazardous materials.